Exactly How to Remove and Change a Tub.
Exactly How to Remove and Change a Tub.
Blog Article
Presented here below you might get a lot of really good expertise around How to Install a Bathtub Yourself.
Setting up a bath tub isn't exactly rocket science, yet it does require solid plumbing, woodworking, and sometimes, tiling abilities. Changing an old bathtub with a new one is additionally a reasonably difficult job. If the old bathtub is readily available, the job can relocate quickly; if you have to open up a wall surface to get rid of the old tub and position the brand-new bath tub, the task is much harder. In either situation, the job is within a residence handyman's abilities, although you will need a helper to vacate the old bathtub and set in the new one. Make certain you have actually certified on your own for the job and are comfortable trying it. As opposed to working with a contractor to take over a halfway-completed job, it is much better to take into consideration utilizing one prior to you start. Opportunities are you might need a professional plumber to make tube connections.
This short article will assist you set up a brand-new bath tub in your washroom if you have actually currently acquired a brand-new bathtub and also do not require to transform the setup of your previous water system pipelines.
Your tools and material list need to consist of the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your installation, after that the first thing you need to do is separate the water. After doing so, activate the faucets to drain pipes any type of water remaining in the system. The process of removing the existing faucets can be fairly troublesome because of the restricted access that is often the case.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the remaining water that will certainly originate from the pipes. Once the supply pipelines have actually been eliminated, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from transforming during this process. As soon as the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing compound.
Prior to going on to fit the new taps, contrast the pipe connections on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will require a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end provides a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need reducing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the tap in the placing hole in the bath/basin making sure that the washing machines are in area between the faucet and also the sink. Safeguard the tap in position with the producer provided backnut. When the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with normal tap adapters. The former kind needs to be connected to the tap finishes first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.
Installing the Bathtub
Utilizing both wooden boards under its feet, put the tub in the called for placement. The wood boards are useful in uniformly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 small points.
The following objective is to ensure that the bathtub is leveled all round. This can be accomplished by examining the level and adjusting the feet on the tub up until the level reviews level.
To install taps, fit all-time low of the outermost adaptable faucet connector to the appropriate supply pipe by making a compression join; after that do the very same for the various other tap.
Switch on the supply of water as well as inspect all joints as well as brand-new pipework for leakages and also tighten them if necessary. Fill the bathtub and likewise inspect the overflow electrical outlet as well as the typical electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the supplier's user's manual. Tiling and also securing around the bath tub needs to wait till the bath tub has actually been made use of at the very least when as this will certainly resolve it right into its last placement.
Planning for the Installment
To start with, the sustaining framework provided with the bath ought to be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is important to make sure that if the faucet features a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps unit to prevent pressure on the bath tub.
Fit the versatile tap connectors to the bottom of the two faucets making use of 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you make use of all of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be suited its final position.
Tiling Around the Bath tub
In the location where the bath meets the floor tile, it is essential to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move sufficient to split a rigid seal, creating the water to pass through the wall between the bath and the tiling, bring about issues with dampness and also feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your components as well as fittings. They are offered in tubes and cartridges, as well as can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of soaked paper or soft rope. Remember to constantly load the bathtub with water prior to securing, to enable the activity experienced when the tub remains in usage. The sealant can fracture fairly very early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily offered on the market. It is a good idea to fit the tiles utilizing waterproof or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very serious about Installing A Bathtub and I really hope you liked the article. In case you enjoyed reading our page please remember to share it. We recognize the value of reading our article about Installing A Bathtub.
Source This Article Report this page